Use with both vacuums and air pressure.

  • Corrosion-resistant stainless steel and brass construction.
Part Number 56-15C18BTF
Dial Diameter 1.5″
Pressure Range Shown 0-30 in of Hg, 0-100 psi
Connector Size 1/8″ NPT Male
Mount Location Bottom
How to Zero Liquid-Filled Gauges
    1. Locate the vent hole on the gauge. It is usually a small hole with a rubber stopper or a brass pin.
    2. Insert a fingernail or a small screwdriver into the vent hole and apply pressure*. This will release the pressure in the gauge and the pointer will return to zero.
    3. If the gauge has a brass pin, you may need to pull the pin out to release the pressure.
    4. Once the pressure is released, the pointer should return to zero. If it does not, you may need to repeat the steps above.

*NOTE: Be careful when pushing on the stopper; it has the potential to fall into the gauge, and will be difficult to remove.


How to Measure Fittings & Suction Cup Heights

Downloads

DOCUMENT

CATEGORY

LINK

SIZE

BLICK INDUSTRIES Catalog

Catalog

https://www.blickindustries.com/wp-content/uploads/2022/08/BLICK_2022_Catalog_web.pdf

23 MB

How to Measure Suction Cup Heights & Air Fittings

Fittings

https://www.blickindustries.com/wp-content/uploads/2020/02/BLICK_Fittings-SuctionCups_20200210_Measurments.pdf

397 KB

Anatomy of a Suction Cup

Suction Cups

https://www.blickindustries.com/wp-content/uploads/2022/06/Anatomy200x200_20220620.pdf

2 MB

Suction Cup Seal Lengths

Suction Cups

https://www.blickindustries.com/wp-content/uploads/2023/12/SuctionCup_SealChart_20231221.pdf

829 KB

How to Measure Valves

Fittings

https://www.blickindustries.com/wp-content/uploads/2020/12/BLICK_Valve-Port-Mani_20201202_Measur.pdf

333 KB

Isolator Kit

Tools & Accessories: Vacuum Systems

https://www.blickindustries.com/wp-content/uploads/2024/11/BlickIndustries_IsolatorKit_20241105.pdf

937 KB

Leatherheads & Accessories

Tools & Accessories

https://www.blickindustries.com/wp-content/uploads/2024/03/BLICK_Leatherheads+Accessories_20240224.pdf

2.24 MB

Repair Form

Forms

https://www.blickindustries.com/wp-content/uploads/2022/11/Blick_Repair-Form_20221130.pdf

82 KB

Dimensions Diagram - 26 mm Edge Locating Pin

Locating Devices

https://www.blickindustries.com/wp-content/uploads/2020/09/BLICK_26mm-Edge-Locat-Pin_20200803.pdf

KB

Dimensions Diagram - 50 mm Edge Locating Pin

Locating Devices

https://www.blickindustries.com/wp-content/uploads/2020/09/BLICK_50mm-Edge-Locat-Pin_20200803.pdf

484 KB

Dimensions Diagram - 50 mm Edge Locating Pin EL

Locating Devices

https://www.blickindustries.com/wp-content/uploads/2022/08/BLICK_50mm-Edge-Locat-Pin-EL_20200803.pdf

483 KB

Incoming Vacuum Lines - Manifold for INTERMAC Machine (Right)

Manifolds

https://www.blickindustries.com/wp-content/uploads/2020/08/21-101-02_Intermac-Mani_20200828.pdf

844 KB

Incoming Vacuum Lines - Manifold for INTERMAC Machine (Left)

Manifolds

https://www.blickindustries.com/wp-content/uploads/2020/08/21-101-01_Intermac-Mani_20200828.pdf

855 KB

Replacement Parts - Intermac Manifolds

Manifolds

https://www.blickindustries.com/wp-content/uploads/2020/08/INTERMAC-Mani_Replace-Parts_20200828.pdf

134 KB

Height Diagram - Stop Locator Tool

Locating Devices

https://www.blickindustries.com/wp-content/uploads/2020/08/Stop-Locator-Tool-Diagram.pdf

929 KB

Dressing Tool Assembly & Body Lengths

Tools & Accessories

https://www.blickindustries.com/wp-content/uploads/2020/08/20-022-0x_Dressing-Tool-Assembly_20190520_All_1920.pdf

1 MB

Overview - Backsplash Clamp System

Clamps

https://www.blickindustries.com/wp-content/uploads/2018/06/BSClampInstructions.pdf

66 KB

Blowback Kit Setup Diagram

Manifolds

https://www.blickindustries.com/wp-content/uploads/2021/03/BlowbackKit_SetupDiagram_20210219.pdf

38 KB

Ghost Markings

Service & Repairs

https://www.blickindustries.com/wp-content/uploads/2024/04/BI_Vacuum-Pod_Ghost-Mark_Info.pdf

3 MB

This website uses cookies to improve your experience. By using this website you agree to our Data Protection Policy.
Read more