Corrosion-resistant stainless steel and brass construction.

NOTE: Use with VACUUM ONLY.

Part Number 56-15V18BKF
Dial Diameter 1.5″
Pressure Range Shown 0-30 in of Hg
Connector Size 1/8″ NPT Male
Mount Connection Back
How to Zero Liquid-Filled Gauges
    1. Locate the vent hole on the gauge. It is usually a small hole with a rubber stopper or a brass pin.
    2. Insert a fingernail or a small screwdriver into the vent hole and apply pressure*. This will release the pressure in the gauge and the pointer will return to zero.
    3. If the gauge has a brass pin, you may need to pull the pin out to release the pressure.
    4. Once the pressure is released, the pointer should return to zero. If it does not, you may need to repeat the steps above.

*NOTE: Be careful when pushing on the stopper; it has the potential to fall into the gauge, and will be difficult to remove.

 


How to Measure Fittings & Suction Cup Heights

Reviews
Downloads

CATEGORY

DOCUMENT

LINK

SIZE

Catalog

BLICK INDUSTRIES Catalog

https://www.blickindustries.com/wp-content/uploads/2022/08/BLICK_2022_Catalog_web.pdf

23 MB

Fittings

How to Measure Suction Cup Heights & Air Fittings

https://www.blickindustries.com/wp-content/uploads/2020/02/BLICK_Fittings-SuctionCups_20200210_Measurments.pdf

397 KB

Suction Cups

Anatomy of a Suction Cup

https://www.blickindustries.com/wp-content/uploads/2022/06/Anatomy200x200_20220620.pdf

2 MB

Suction Cups

Suction Cup Seal Lengths

https://www.blickindustries.com/wp-content/uploads/2023/12/SuctionCup_SealChart_20231221.pdf

829 KB

Fittings

How to Measure Valves

https://www.blickindustries.com/wp-content/uploads/2020/12/BLICK_Valve-Port-Mani_20201202_Measur.pdf

333 KB

Tools & Accessories

Leatherheads & Accessories

https://www.blickindustries.com/wp-content/uploads/2021/02/BLICK_LeatherheadsAccessories_20210218.pdf

2.24 MB

Forms

Repair Form

https://www.blickindustries.com/wp-content/uploads/2022/11/Blick_Repair-Form_20221130.pdf

82 KB

Locating Devices

Dimensions Diagram - 26 mm Edge Locating Pin

https://www.blickindustries.com/wp-content/uploads/2020/09/BLICK_26mm-Edge-Locat-Pin_20200803.pdf

KB

Locating Devices

Dimensions Diagram - 50 mm Edge Locating Pin

https://www.blickindustries.com/wp-content/uploads/2020/09/BLICK_50mm-Edge-Locat-Pin_20200803.pdf

484 KB

Locating Devices

Dimensions Diagram - 50 mm Edge Locating Pin EL

https://www.blickindustries.com/wp-content/uploads/2022/08/BLICK_50mm-Edge-Locat-Pin-EL_20200803.pdf

483 KB

Manifolds

Incoming Vacuum Lines - Manifold for INTERMAC Machine (Right)

https://www.blickindustries.com/wp-content/uploads/2020/08/21-101-02_Intermac-Mani_20200828.pdf

844 KB

Manifolds

Incoming Vacuum Lines - Manifold for INTERMAC Machine (Left)

https://www.blickindustries.com/wp-content/uploads/2020/08/21-101-01_Intermac-Mani_20200828.pdf

855 KB

Manifolds

Replacement Parts - Intermac Manifolds

https://www.blickindustries.com/wp-content/uploads/2020/08/INTERMAC-Mani_Replace-Parts_20200828.pdf

134 KB

Locating Devices

Height Diagram - Stop Locator Tool

https://www.blickindustries.com/wp-content/uploads/2020/08/Stop-Locator-Tool-Diagram.pdf

929 KB

Tools & Accessories

Dressing Tool Assembly & Body Lengths

https://www.blickindustries.com/wp-content/uploads/2020/08/20-022-0x_Dressing-Tool-Assembly_20190520_All_1920.pdf

1 MB

Clamps

Overview - Backsplash Clamp System

https://www.blickindustries.com/wp-content/uploads/2018/06/BSClampInstructions.pdf

66 KB

Manifolds

Blowback Kit Setup Diagram

https://www.blickindustries.com/wp-content/uploads/2021/03/BlowbackKit_SetupDiagram_20210219.pdf

38 KB

1.5″ Oil Filled Vacuum Gauge – Back Mount

$35.00

Replacement gauge for the single and double vacuum generator kits.

1.5″ Oil Filled Vacuum Gauge – Back Mount

Replacement gauge for the single and double vacuum generator kits.


$35.00

Corrosion-resistant stainless steel and brass construction.

NOTE: Use with VACUUM ONLY.

Part Number 56-15V18BKF
Dial Diameter 1.5″
Pressure Range Shown 0-30 in of Hg
Connector Size 1/8″ NPT Male
Mount Connection Back
How to Zero Liquid-Filled Gauges
    1. Locate the vent hole on the gauge. It is usually a small hole with a rubber stopper or a brass pin.
    2. Insert a fingernail or a small screwdriver into the vent hole and apply pressure*. This will release the pressure in the gauge and the pointer will return to zero.
    3. If the gauge has a brass pin, you may need to pull the pin out to release the pressure.
    4. Once the pressure is released, the pointer should return to zero. If it does not, you may need to repeat the steps above.

*NOTE: Be careful when pushing on the stopper; it has the potential to fall into the gauge, and will be difficult to remove.

 


How to Measure Fittings & Suction Cup Heights

Reviews
Downloads

CATEGORY

DOCUMENT

LINK

SIZE

Catalog

BLICK INDUSTRIES Catalog

https://www.blickindustries.com/wp-content/uploads/2022/08/BLICK_2022_Catalog_web.pdf

23 MB

Fittings

How to Measure Suction Cup Heights & Air Fittings

https://www.blickindustries.com/wp-content/uploads/2020/02/BLICK_Fittings-SuctionCups_20200210_Measurments.pdf

397 KB

Suction Cups

Anatomy of a Suction Cup

https://www.blickindustries.com/wp-content/uploads/2022/06/Anatomy200x200_20220620.pdf

2 MB

Suction Cups

Suction Cup Seal Lengths

https://www.blickindustries.com/wp-content/uploads/2023/12/SuctionCup_SealChart_20231221.pdf

829 KB

Fittings

How to Measure Valves

https://www.blickindustries.com/wp-content/uploads/2020/12/BLICK_Valve-Port-Mani_20201202_Measur.pdf

333 KB

Tools & Accessories

Leatherheads & Accessories

https://www.blickindustries.com/wp-content/uploads/2021/02/BLICK_LeatherheadsAccessories_20210218.pdf

2.24 MB

Forms

Repair Form

https://www.blickindustries.com/wp-content/uploads/2022/11/Blick_Repair-Form_20221130.pdf

82 KB

Locating Devices

Dimensions Diagram - 26 mm Edge Locating Pin

https://www.blickindustries.com/wp-content/uploads/2020/09/BLICK_26mm-Edge-Locat-Pin_20200803.pdf

KB

Locating Devices

Dimensions Diagram - 50 mm Edge Locating Pin

https://www.blickindustries.com/wp-content/uploads/2020/09/BLICK_50mm-Edge-Locat-Pin_20200803.pdf

484 KB

Locating Devices

Dimensions Diagram - 50 mm Edge Locating Pin EL

https://www.blickindustries.com/wp-content/uploads/2022/08/BLICK_50mm-Edge-Locat-Pin-EL_20200803.pdf

483 KB

Manifolds

Incoming Vacuum Lines - Manifold for INTERMAC Machine (Right)

https://www.blickindustries.com/wp-content/uploads/2020/08/21-101-02_Intermac-Mani_20200828.pdf

844 KB

Manifolds

Incoming Vacuum Lines - Manifold for INTERMAC Machine (Left)

https://www.blickindustries.com/wp-content/uploads/2020/08/21-101-01_Intermac-Mani_20200828.pdf

855 KB

Manifolds

Replacement Parts - Intermac Manifolds

https://www.blickindustries.com/wp-content/uploads/2020/08/INTERMAC-Mani_Replace-Parts_20200828.pdf

134 KB

Locating Devices

Height Diagram - Stop Locator Tool

https://www.blickindustries.com/wp-content/uploads/2020/08/Stop-Locator-Tool-Diagram.pdf

929 KB

Tools & Accessories

Dressing Tool Assembly & Body Lengths

https://www.blickindustries.com/wp-content/uploads/2020/08/20-022-0x_Dressing-Tool-Assembly_20190520_All_1920.pdf

1 MB

Clamps

Overview - Backsplash Clamp System

https://www.blickindustries.com/wp-content/uploads/2018/06/BSClampInstructions.pdf

66 KB

Manifolds

Blowback Kit Setup Diagram

https://www.blickindustries.com/wp-content/uploads/2021/03/BlowbackKit_SetupDiagram_20210219.pdf

38 KB


This website uses cookies to improve your experience. By using this website you agree to our Data Protection Policy.
Read more